Drywall Calculator

Enter your room size and pick a sheet size. We count the sheets for the walls and ceiling and estimate the mud, tape and screws.

Updated Nov 2026 Formula shown below Feet or meters
ft
Enter a number (0 or more)
ft
Enter a number (0 or more)
ft
Enter a number (0 or more)
Enter a number (0 or more)
Enter a number (0 or more)
%
10–15% is typicalEnter a number (0 or more)
What are you covering?
Your prices (optional)
$each
Enter a number (0 or more)
You'll need
–
mud, sand, repeat

How to calculate drywall for a room

Drywall is sold by the sheet, so the job is to find the surface you need to cover and divide it by the size of one sheet. Measure around the room, multiply by the wall height, take away doors and windows, and add the ceiling if you're covering it too.

Sheets = (Walls − Openings + Ceiling) × (1 + Waste %) ÷ Sheet area

The wall area is the perimeter, 2 × (length + width), times the wall height. We count a door as 21 sq ft and a window as 15 sq ft. A 4 × 8 sheet covers 32 sq ft, a 4 × 10 covers 40 and a 4 × 12 covers 48. Add 10–15% for cuts, because offcuts around openings and corners are rarely big enough to reuse.

Pro tip!

Hang the ceiling first, then the walls. The wall sheets push up against the ceiling edges and help hold them in place.

Worked example: a 12 × 12 ft bedroom

A square bedroom with 8-foot walls, one door and two windows. You're covering the walls and the ceiling with 4 × 8 sheets.

  1. Find the wall area2 × (12 + 12) × 8 = 384 sq ft
  2. Subtract 1 door and 2 windows384 − 21 − 30 = 333 sq ft
  3. Add the ceiling333 + 144 = 477 sq ft
  4. Add 10% for waste477 × 1.10 = 524.7 sq ft
  5. Divide by one sheet524.7 ÷ 32 = 16.4 → 17 sheets

For finishing, the same room needs about 5 gallons of joint compound, about 177 feet of tape and roughly 544 screws (17 sheets × 32).

How much mud, tape and screws?

These are rough rules of thumb for a standard three-coat finish. Your own numbers will change with the finish level, the number of corners and how heavy a hand you have with the knife.

SupplyRule of thumbNotes
Joint compoundAbout 1 gal per 100 sq ftPremixed, all three coats
Paper joint tapeAbout 37 ft per 100 sq ftSold in 250 and 500-ft rolls
ScrewsAbout 1 per sq ft of boardGenerous on purpose: wall spacing works out to about 25 per 4 × 8 sheet, ceilings take more, and some always get dropped

Which sheet size should you buy?

SheetCoversGood for
4 × 8 ft32 sq ftEasiest to carry, small rooms, DIY
4 × 10 ft40 sq ftWalls a little over 8 ft, or hung upright on 10-ft walls
4 × 12 ft48 sq ftLong walls and ceilings with fewer seams

Most interior walls use ½-inch board. Some spots call for thicker or fire-rated board, so check local codes.

Questions people ask

How many sheets of drywall do I need for a 12 × 12 room?

With 8-foot walls, one door, two windows and 10% extra, about 12 sheets of 4 × 8 for the walls alone, or 17 if you also cover the ceiling.

How much joint compound do I need?

A common rule of thumb is about 1 gallon of premixed compound per 100 square feet of drywall for three coats. Textured finishes and extra coats use more.

How many screws go in a sheet of drywall?

With the usual spacing, about 25–28 on a 4 × 8 sheet on walls, and more on ceilings, where screws go closer together. We estimate one per square foot of board (32 per 4 × 8 sheet) so you have spares.

Should I subtract doors and windows?

We take off about 21 sq ft per door and 15 sq ft per window. Many installers hang full sheets over small openings and cut them out, which the waste allowance covers.

Sources

The numbers in this calculator come from these manufacturer specs and public guides. Always check the label on the product you buy.

  1. Joint compound (about 9 gal) and tape (350–375 ft) per 1,000 sq ft — National Gypsum
Was this calculator helpful?

Finishing a whole basement?

See all calculators